Maverick, Inc

Boom, Auger, Drive Parts, Teeth and Accessories for DitchWitch®

Teeth and Accessories for DitchWitch® Trencher Models M Series, C Series, J-20, 1410, 1420, 1500, & 1810 Using 1" Hole Spacing on Side Bars for Cutters

Image of numbered parts

Replacement Drive Shaft for DitchWitch® Models C7, C9, C77 & C99

Ref No. Part No. Description Weight (lbs.)
22 B 165-443 Head Shaft (Replaces # B 165-382) 11
23 B 105-330 Nut (1-3/8" NF) (Replaces # B 105-380) 0.25
24 B 105-331 Lockwasher (1-3/8" NF) (Replaces # B 105-381) 0.06
N/S B 105-461 Tang Washer - Not Shown 0.06

Drive Parts for Models M & M422 Series Trenchers

Image of numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B 165-415 Head Shaft, 8" Pivot - 31" Long 13
N/S B 165-416 Head Shaft, 12" Pivot - 341⁄2" Long 15
2 B 165-944 Key (1⁄4" x 13⁄4") 0.10
3 B 105-067 Bolt (1⁄2" N.C. x 23⁄4") 0.06
4 B 105-065 Nut Lock 1⁄2" N.C. 0.06
5 B 180-031 Dirt Shield 0.1
6 B 180-037 Spacer Seal 0.2
7 B 155-802 Seal 0.0
8 B 110-003 Bearing Shield 0.06
9 B 125-204 Cone Bearing 0.19
10 B 125-203 Cone Bearing W/ Seal 0.44
11 B 125-205 Bearing Cup 0.19
12 B 115-454 Retaining Ring 0.06
13 B 180-035 8" Pivot Spacer 1.5
N/S B 180-036 12" Pivot Spacer 3.5
14 B 180-032 Spacer 0.1
N/S B 105-461 Tang Washer 0.06
15 B 105-331 Lock Washer 0.06
16 B 105-330 Adjusting Nut 0.2
17 B 115-465 Retaining Ring 0.06
N/S B 105-704 5⁄16" Set Screws 0.06
18 B 140-702 Drive Sprocket, 13⁄8" Bore 4
19 B 145-047 Auger 25
20 B 105-352 Adjusting Screw 0.63
21 B 140-038 Adjusting Block 1.5

Adjusting Miscellaneous Parts (not shown) for Model M

Part No. Description Weight (lbs.)
B 140-718* Sprocket Head Shaft 11⁄8” Bore (M3 - M389) 4.5
B 140-720* Sprocket Head Shaft 11⁄4” Bore (M3 - 22 or M329) 2.5
B 125-010 Drive Shaft Bearing (M2, M3) 0.7
B 155-814 Head Shaft Seal (M3, M389) 0.05
B 155-815 Dust & Dirt Seal (M3 - M389) 0.1
B 165-320 Head Shaft Drive - 8” Pivot (M3 or M389) 8.65
B 165-321 Head Shaft Drive - 12” Pivot (M3 or M329) 12
B 170-002 V Belt Set (3) (Model M3) 2.2
B 170-005 V Belt Set (3) (Model M) 3

* Measure bore size


Boom, Auger and Drive Parts for DitchWitch® Models M Series, 1410, 1420, 1500, 1810, 1620, 350SX, 400SX & Model 2020 using Sprocket Boom

Image of numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B 105-352 Square Head Set Screw 0.63
2 B 140-038 Boom Adj. Block 1.5
3 B 105-515 Cotter Pin (3⁄16" x 3") 0.06
4 B 140-551 Boom Extension, 1' 11
N/S B 140-552 Boom Extension, 2' 16
5 B 180-445 Sq. Idler Shaft 0.2
6 B 140-775 Dirt Shield (2 Required) 0.25
7 B 140-759 Boom End Slide & Stop, Less Sprocket 11.07
8 B 115-464 Retaining Ring 0.06
9 B 115-554 Boom Spring 1.15
10 B 140-028 Sleeve, Boom 0.39
11 B 140-712 Idler, Sprocket 6.5
N/S B 140-653 Sprocket Assembly (includes ref. #’s 11, 8, 14, 6) 7.85
12 B 105-379 Bolt (3⁄4" NC x 11⁄4") 0.9
13 B 125-009 Idler Sprocket, Bearing 1.5
14 B 140-051 Boom without Sprocket Assembly 21.53
N/S B 140-060 Boom Complete with Slide & Stop, 2 Sprockets 54
15 B 142-006 Split Sprocket (142-039) 6.18
16 B 181-361 Hub for 1410/1420 5
N/S B 184-017 Hub for 1620 5
17 B 145-204 Auger – 1410 & 1420 Only 27.90
N/S B 145-183 Auger – 1810 Only -
18 B 140-703 Drive Sprocket (1410, 1420, 1810 & 1500) 4.2
N/S B 130-124 Drive Chain 1420 #50-92p (not shown) 3.36

Boom and Drive Parts for DitchWitch® Models C-7, C-9, C77, C99 & 350SX

Image of numbered parts

Image of numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B 140-088 Boom Assembly (Less Sprocket) 17
N/S B 140-090 Boom Assembly (With Sprocket) 26
2 B 140-499 Boom Only -
N/S B 140-498 Boom Assembly -
3 B 140-712 Sprocket 6.5
N/S B 140-653 Sprocket Assembly (includes ref. #’s 2, 6, 7, 8) 7.5
4 B 140-770 Slide & Stop 6.5
5 B 115-553 Boom End Spring 0.63
6 B 115-001 Zerk Fitting (1⁄8" NPT Str) 0.06
7 B 140-775 Washer, Shield 0.25
8 B 125-009 Bearing, Idler Sprocket 1.5
9 B 115-464 Snap Ring, Idler Sprocket 0.06
10 B 180-445 Idler Shaft 1
11 B 105-379 Bolt (3⁄4" x 11⁄4") 0.19
12 B 105-372 Lock Nut (3⁄4") 0.1
13 B 140-794 Boom End 7.6
14 B 105-352 Square Head Set Screw 0.63
15 B 145-099 Auger 15
16 B 115-465 Snap Ring 0.06
17 B 140-703 Drive Sprocket 13⁄8" Bore 4.2
18 B 110-003 Machinery Bushing 0.1
19 B 155-802 Seal 0.1
20 B 125-204 Bearing 0.19
21 B 125-203 Bearing 0.44
22 B 125-205 Race 0.19
23 B 180-037 Seal Cover 0.2
24 B 180-031 Dirt Shield 0.1
25 B 115-657 Urethane Washer 0.06
26 B 170-033 Belt Set (3 Belts) 2.75
27 B 130-006 Drive Chain (101 P) #40RC 1.75
28 B 130-008 Drive Chain (103 P) #40 RC 2
29 B 130-001 Connector Link 0.09
30 B 130-002 Offset Link 0.0.2
31 B 140-028 Boom Sleeve 0.5
32 B 105-047 Locknut (3⁄8") 0.06
N/S B 170-006 Belt Set, C49 - Steel Cable (2) 1.5
N/S B 170-001 Belt Set, (2) Models (C2, C3, C4, C49) 1
N/S B 105-146 Bolt (3⁄8" NC x 21⁄4") 0.06

Boom Parts, Sprockets, Bearings, and Accessories for DitchWitch® Models R40, R60, R65, 4010, 5010, 6510, 7510, 7610, 8020 & Attachments A/H400, A/H500, H700

Image of Numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B 140-013 Boom Sleeve 0.5
2 B 140-021 Boom Spring 0.8
3 B 140-758 Slide & Stop 25.6
4 B 180-440 Idler Shaft (Slide & Stop) 3
5 B 105-377 Nut 0.5
6 B 140-723 Idler Sprocket (Bearing Kit for Idler Sprocket: see * below) 26.5
- B 140-656 Idler Sprocket Assy, (Includes Sprocket & #’s 7-13) 24.75
7 B 180-244 Spacer Bearing 0.1
8 B 180-243 Spacer Bearing 031
9 B 180-026 Fiber Spacer 0.1
10 B 155-843 Seal 0.15
11 B 125-265 Bearing 1
12 B 125-266 Race 0.6
13 B 115-470 Retaining Ring 0.01
14 B 180-441 Idler Shaft (Boom – Idler) 2.75
15 B 150-191 Grease Cylinder Barrel 3.5
16 B 150-340 Grease Cylinder Rod 5.1
17 B 150-058 Grease Cylinder Assembly 11
18 B 155-711 O Ring 0.03
19 B 155-712 Back-up Ring 0.1
20 B 115-001 Zerk (1⁄8") 0.06
21 B 105-367 Lock Nut (1" NC) 0.25
22 B 105-419 Bolt (1" NC X 4") 1.13
23 B 140-730 Idler Sprocket (2" P) -
- B 140-731A Idler Sprocket Assembly (14T) (140-659) -
24 B 142-756 17" End Roller -
- B 142-756A 17" End Roller Assembly -
* B 140-661 Bearing Kit (includes Reference #’s 7-13) -
N/S B 140-120 Boom Gussets -

Auger Parts & Accessories for Ditch Witch® Models R40, R60, R65, 4010, 5010, 6510, 7510, 8020 & Attachments A/H400,A/H500, H700 (3" P)

Image of Numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B 140-070 Auger, R.H. (24") 53
2 B 145-071 Auger, L.H. (24") 53
3 B 145-109 Auger, R.H. (12") 28
4 B 145-110 Auger, R.H. (12") 28
5 B 105-407 Bolt, (5⁄8" x 4") 0.5
6 B 105-357 Lock Nut (5⁄8") 0.06
7 B 115-001 Zerk 0.06
8 B 125-517 Pillow Block Bearing, 13⁄4" I.D. 10.5
9 B 105-466 Bolt (3⁄4" x 2 1/2") 0.5
10 B 105-372 Lock Nut (3⁄4") 0.06
11 B 105-384 Washer (3⁄4") 0.06
12 B 140-725 Auger Sprocket & Shaft 35
13 B 142-008 Auger Sprocket 23.9
14 B 165-368 Auger Shaft 15
15 B 145-244 Hex Auger Shaft -
16 B 140-665 Auger Sprocket, Hex -
17 B 110-363 Flange (LS) -
18 B 110-364 Flange (NLS) -
19 B 125-620 Hex Bearing Assembly -
20 B 125-048 Hex Bearing -
21 B 145-248 Hex Sprocket Hub -

Drive Sprocket Head Shaft, Components for Ditch Witch® Models R40, R60, R65, 4010, 5010, 6510, 7510, 7610, 8020 & Attachments A/H400,A/H500, H700

Image of Numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B 180-055 Sprocket Hub 3.5
2 B 140-717 Split Sprocket 15
3 B 105-302 Bolt 5⁄8" x 2" 0.25
4 B 180-057 Spacer Seal 2
5 B 155-703 O Ring 0.06
6 B 145-475 Washer 0.03
7 B 155-805 Seal 0.25
8 B 125-259 Bearings 1.5
9 B 125-258 Race 1
10 B 180-071 Backup Ring 0.13
N/S B 145-476 Washer 0.20
11 B 105-384 3⁄4" Washer 0.06
N/S B 105-364 Bolt 3⁄4" X 2" 0.25
N/S B 180-064 Washer 13⁄16" I.D. x 3" O.D. x 1⁄2" 0.62
12 B 165-329 Drive Shaft 38
13 B 165-903 Key (5⁄8" Sq. x 43⁄8" Lg.) 0.25
14 B 165-904 Key (5⁄8" Sq. x 37⁄8" Lg.) 0.25
15 B 165-905 Key (3⁄4" X 5⁄8" x 31⁄4") 0.25
16 B 165-907 Key (5⁄8" R2 x 3⁄8") 0.1
17 B 175-604 Sprocket (100 Q 32) 26.5
18 B 115-003 Zerk (1⁄4 N.F. Str.) 0.03
19 B 105-313 Nut 0.19
20 B 180-062 Dirt Shield 0.19
21 B 141-589 Sprocket Split Drive 11 Tooth -
21 B 125-209 Bearing Assembly 1
22 B 175-605 Sprocket (100-B14) 4.75
N/S B 175-608 Sprocket Assembly 6
N/S B 130-404 Chain (100-65 Pitches) 20
N/S B 130-402 Offset Link 0.35
N/S B 130-401 Connector Link 0.25
23 B 170-038 Power Band V Belts — 2 Belts 1.85
24 B 170-059 Power Band V Belts — 4 Belts 1.96
N/S B 170-609 Sprocket #100 Q 34 28
25 B 142-009 Sprocket (1 Piece) 16
N/S B 175-509 Idler Sprocket #80 – 16 Tooth -
26 B 165-379 Drive Shaft for offset machine -

Rock & Frost Section

Image of Numbered parts

Ref No. Part No. Description Weight (lbs.)
1 B56KRB Carbide Tooth, Rockbuster (.765 HB) -
2 B43KRB Carbide Tooth, Rockbuster (.735 HB) -
3 B56-B Carbide Tooth, Full Cap (.765 CB) -
4 B43-B Carbide Tooth, Full Cap (.735 CB) -
5 B56-C Carbide Tooth, Half Cap (.765 MB) -
6 B43-C Carbide Tooth, Half Cap (.735 MB) -
7 CB43-10 Tooth Pockets (.735 BLK) -
8 CB56-10 Tooth Pockets (.765 BLK) -
9 Puller Tooth Puller (Standard) -
N/S Puller Tooth Puller (Large) -
10 N/A Chain Installer, Small (1.654" through 2") -
N/S N/A Chain Installer, Large (3" through 4") -
11 B43LH Carbide Tooth 1/2 Cap w/clip (.735 MRW) -
12 B43LRB Carbide Tooth Rockbuster w/Clip (.735 HR) -
13 B43LW Lock Washers (K 91) -
N/S C31HD Carbide Tooth, Rockbuster (.990 HB) -
N/S C31 Carbide Tooth, Half Cap (.990 MB) -
N/S .990 CRF Carbide Tooth, Full Cap with Flared Shoulder -
14 B 43 CW Clip Wrench  

Note: We have all styles and sizes of Carbide Bits


Terminator®, Alligator and Bolt-on Rock & Frost Chain, Teeth & Adapters for DitchWitch® Walk Along Models Using 1.654" Pitch Chain & Accessories

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A SH16540426 1.654”P Welded Terminator Chain, 4” Cut, 26 Stations -
2 N/A AL16540426 1.654”P Welded Alligator Chain, 4” Cut, 26 Stations -
3 B 135-316 - Bit Adapter Center 0.5
4 B 135-317 - Bit Adapter L.H. 0.5
5 B 135-318 - Bit Adapter R.H. 0.5
6 B17 - Carbide Bit 0.2
7 B17-D - Lockwasher 0.02
8 B17-10 - Tooth Holder -
9 T165404C - Terminator Adapter, Center 0.75
10 T165404L - Terminator Adapter, L.H. 0.75
11 T165404R - Terminator Adapter, R.H. 0.75
12 TT1654 - Terminator Tooth Only 0.3
13 B 135-319 - Tubular Spacer (Used with Bit Adapter on Inside) -
14 B 135-320 - Tubular Spacer (Used with Bit Adapter on Outside) -
15 B 135-936 - Flat Spacer (3⁄8") (28,000 Lb. - Chain Only) -
16 B 135-937 - 5" Flat Spacer (28,000 Lb. Chain Only) -
17 B 135-938 - 6" Flat Spacer (28,000 Lb. Chain Only) -
18 B 136-027 - 5" Flat Spacer (34,000 & 38,000 Lb. Chain) -
19 B 136-029 - 6" Flat Spacer (34,000 & 38,000 Lb. Chain) -
20 B 105-162 - Bolt 3⁄8" x 2 1⁄4" Used with Bit Adapter on Inside -
21 B 105-915 - Bolt 3⁄8" x 2 3⁄4" Used with Bit Adapter on Outside -
22 B 105-916 - Bolt 3⁄8" x 4 1⁄2" Used with Spacer for 5" Cut -
23 B 105-917 - Bolt 3⁄8" x 5 1⁄2" Used with Spacer for 6" Cut -
24 38LW - Lock Washer 3⁄8" -
25 B 105-047 - Locknut 3⁄8" -
26 B 105-101 - Flat Washer 3⁄8" -
27 B 059-360 - Half Link with Connecting Pin (28,000 Lb. Chain Only) -
28 B 135-001 - Connector Pin with Keeper (All Chains) -

Note: For additional bare chain components, see walk-along section.


Terminator®,Alligator and Bolt-on Rock & Frost Chain,Teeth & Adapters (2" Pitch, 50,000 Lb.Test Chain) for DitchWitch® Models V30, R30, 2300, 2200, 2310, R40, J20, 3500, 3610, 3700, R40, 4500, 4010

Image of Numbered parts

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A SH20000636 2” P Welded Terminator Chain, 6” Cut, 36 Stations -
2 N/A AL200006D36 2” P Welded Alligator Chain, 6” Cut, 36 Stations -
3 T 20034 - Terminator Tooth, 3⁄4”V-Carbide 0.8
4 T 20078 - Terminator Tooth, 7/8”V-Carbide 0.85
5 765 BLK - Tooth Holder 0.8
6 765 HDBLK - Heavy-Duty Tooth Holder 1.0
7 B 105-065 - 1⁄2" Locknut -
8 B 105-076 - (1⁄2" x 3") Bolt -
9 B 105-110 - (1⁄2" x 4 1⁄2") Bolt -
10 B 105-111 - (1⁄2" x 4") Bolt -
11 B 135-952 - Chain Spacer (Used with Bit Adapter on Outside) -
12 B 135-043 - Chain Spacer (Used with Bit Adapter on Inside) -
13 B 135-958 - Carbide Bit Half Cap (B56-C) (765 MB) 0.5
14 B 135-959 - Carbide Bit Full Cap (B56-B) (765 CB) 0.5
15 B 135-058 - Carbide Rockbuster (CB56KRB) (765 HB) 0.5
16 B 136-036 - Bit Adapter (Less Bit) R.H. Center - Through 4" 2.3
17 B 136-037 - Bit Adapter (Less Bit) L.H. Center - Through 4" 2.3
18 B 136-038 - Bit Adapter (Less Bit) L.H. 5" 2.3
19 B 136-039 - Bit Adapter (Less Bit) R.H. 5" 2.3
20 B 136-041 - Bit Adapter (Less Bit) L.H. 6" 2.3
21 B 136-040 - Bit Adapter (Less Bit) R.H. 6" 2.3
22 T 20004L - Terminator Adapter, L.H. C-4” 2.3
23 T 20004R - Terminator Adapter, R.H. C-4” 2.3
24 T 20005L - Terminator Adapter, L.H. 5” 2.3
25 T 20005R - Terminator Adapter, R.H. 5” 2.3
26 T 20006L - Terminator Adapter, L.H. 6” 2.3
27 T 20006R - Terminator Adapter, R.H. 6” 2.3
N/S T 20008L - Terminator Adapter, L.H. 8” 2.3
N/S T 20008R - Terminator Adapter, R.H. 8” 2.3

Note: For additional bare chain components, see 2” pitch chain section.


Terminator®,Alligator and Bolt-on Rock & Frost 2" Pitch Anti-Back Flex Chain,Teeth & Adapters for DitchWitch® Models V30, R30, 2300, 2310, R40, 4010, 5010, 3500, 2200, 3610, 3700, 4500

Image of Numbered parts

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A SH20000636 2” P Welded Terminator Chain, 6” Cut, 36 Stations -
2 N/A AL200006D36 2” P Welded Alligator Chain, 6” Cut, 36 Stations -
3 T 20034 - Terminator Tooth, 3⁄4”V-Carbide 0.8
4 T 20078 - Terminator Tooth, 7/8”V-Carbide 0.85
5 765 BLK - Tooth Holder 0.8
6 765 HDBLK - Heavy-Duty Tooth Holder 1.0
7 B 105-065 - 1⁄2" Locknut -
8 B 105-076 - (1⁄2" x 3") Bolt -
9 B 105-110 - (1⁄2" x 4 1⁄2") Bolt -
10 B 105-111 - (1⁄2" x 4") Bolt -
11 B 135-952 - Chain Spacer (Used with Bit Adapter on Outside) -
12 B 135-043 - Chain Spacer (Used with Bit Adapter on Inside) -
13 B 135-958 - Carbide Bit Half Cap (B56-C) (765 MB) 0.5
14 B 135-959 - Carbide Bit Full Cap (B56-B) (765 CB) 0.5
15 B 135-058 - Carbide Rockbuster (CB56KRB) (765 HB) 0.5
16 B 136-036 - Bit Adapter (Less Bit) R.H. Center - Through 4" 2.3
17 B 136-037 - Bit Adapter (Less Bit) L.H. Center - Through 4" 2.3
18 B 136-038 - Bit Adapter (Less Bit) L.H. 5" 2.3
19 B 136-039 - Bit Adapter (Less Bit) R.H. 5" 2.3
20 B 136-040 - Bit Adapter (Less Bit) R.H. 6" 2.3
21 B 136-041 - Bit Adapter (Less Bit) L.H. 6" 2.3
22 T 20004L - Terminator Adapter, L.H. C-4” 2.3
23 T 20004R - Terminator Adapter, R.H. C-4” 2.3
24 T 20005L - Terminator Adapter, L.H. 5” 2.3
25 T 20005R - Terminator Adapter, R.H. 5” 2.3
26 T 20006L - Terminator Adapter, L.H. 6” 2.3
27 T 20006R - Terminator Adapter, R.H. 6” 2.3
N/S T 20008L - Terminator Adapter, L.H. 8” 2.3
N/S T 20008R - Terminator Adapter, R.H. 8” 2.3

Note: For additional bare chain components, see 2” pitch ABF chain section.


Terminator®,Alligator and Bolt-on Rock & Frost Chain,Teeth & Adapters for DitchWitch® Models R60, R65, R6510, R40, 4010, 5010, 7510, 7610, 8020 Using 3.067"P Chain

Image of Numbered parts

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A SH3067HD0632 3”P, 110,000 Lb.Welded Terminator Chain, 6” Cut, 32 Sta. -
2 N/A AL30670632 3”P, 110,000 Lb.Welded Alligator Chain, 6” Cut, 32 Sta. -
3 T 20034 - Terminator Tooth, 3⁄4" V-Carbide 0.8
4 T 20078 - Terminator Tooth, 7⁄8" V-Carbide 0.85
5 765 BLK - Tooth Holder 0.8
6 765 HDBLK - Heavy Duty Tooth Holder 1.0
7 B 105-322 - Bolt (3⁄4" x 51⁄2") -
8 B 105-365 - Bolt (3⁄4" x 4") -
9 B 105-372   Locknut (3⁄4")  
10 B 105-111 - Bolt (3⁄4" x 4 1⁄2") -
11 B 135-958 - Carbide Bit Half Cap (B56-C) (765 MB) -
12 B 135-959 - Carbide Bit Full Cap (B56-B) (765 CB) -
13 B 135-058 - Carbide Bit Rockbuster (CB56KRB) (765 HB) -
14 B 135-973 - Bit Adapter (Less Teeth) L.H. 8" Cut -
15 B 135-974 - Bit Adapter (Less Teeth) R.H. 8" Cut -
16 B 135-975 - Bit Adapter (Less Teeth) R.H. cc - 6" -
17 B 135-976 - Bit Adapter (Less Teeth) L.H. cc - 6" -
18 T 306706L - Terminator Adapter, L.H. 6” -
19 T 306706R - Terminator Adapter, R.H. 6” -
20 T 306708L - Terminator Adapter, L.H. 8” -
21 T 306708R - Terminator Adapter, R.H. 8” -
22 B 105-373 - Bolt ( 3⁄4" x 5") -
23 B 135-977 - Chain Spacer, Outside (110,000 Lb.) -
24 B 135-978 - Chain Spacer, Inside (110,000 Lb.) -
N/S B 135-979 - Chain Spacer, Outside (70,000 Lb. -
N/S B 135-980 - Chain Spacer, Inside (70,000 Lb.) -

 


Terminator®,Alligator and Bolt-on Rock & Frost 3.067" Pitch Anti-Back Flex Chain,Teeth & Adapters for DitchWitch® Models R60, R65, R6510, R40, 4010, 5010, 7510, 7610, 8020 & Attachments A/H500,A/H700

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A SH3067HD0632 ABF, 110,000# Welded Terminator, 6” Cut, 32 Stations -
2 N/A AL3067ABF06D32 ABF, 110,000# Welded Alligator, 6” Cut, 32 Stations -
3 T 20034 - Terminator Tooth, 3⁄4" V-Carbide 0.8
4 T 20078 - Terminator Tooth, 7⁄8" V-Carbide 0.85
5 765 BLK - Tooth Holder 0.8
6 765 HDBLK - Heavy Duty Tooth Holder 1.0
7 B 105-322 - Bolt (3⁄4" x 5 1⁄2") Used with Two Outside Bit Adapters -
8 B 105-365 - Bolt (3⁄4" x 4") Used with Inside Bit Adapter -
9 B 105-372 - Locknut (3⁄4") -
10 B 105-373 - Bolt (3⁄4" x 5") Used with Outside Bit Adapter -
11 B 135-958 - Carbide Bit Half Cap (B56-C) (765 MB) -
12 B 135-959 - Carbide Bit Full Cap (B56-B) (765 CB) -
13 B 135-058 - Carbide Rockbuster (CB56KRB) (765 HB) -
14 B 135-973 - Bit Adapter L.H. 8" -
15 B 135-974 - Bit Adapter R.H. 8" -
16 B 135-975 - Bit Adapter R.H. Center through 6" Cut -
17 B 135-976 - Bit Adapter L.H. Center through 6" Cut -
18 T 306706L - Terminator Adapter, L.H. 6” -
19 T 306706R - Terminator Adapter, R.H. 6” -
20 T 306708L - Terminator Adapter, L.H. 8” -
21 T 306708R - Terminator Adapter, R.H. 8” -
22 B 135-977 - Chain Spacer (Used with Bit Adapter on Outside) -
23 B 135-978 - Chain Spacer (Used with Bit Adapter on Inside) -

H-Plate,Terminator®, and Bolt-on Rock & Frost Chain,Teeth and Adapters for TA3110 Ultra Heavy-Duty Chain (165,000# Test Chain) Replaces all 3"P Chains

Image of Numbered parts

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A TA311006H32 Welded H-Plate Chain, 6” Cut, 32 Stations -
2 N/A SH31100632 Welded Terminator Chain, 6” Cut, 32 Stations -
3 B 43 LH - Carbide Tooth with clip (735MRW) -
4 B 43 LC - Lock Clip Only (K91) -
5 B 43 LRB - Rockbuster Bit with clip -
6 765 CRFN - Full Cap Carbide Bit with clip -
7 B 43 CW - Clip Wrench -
8 TA 4134 LPL - Cutter, L.H., Low-profile -
9 TA 4134 LPR - Cutter, R.H., Low-profile -
10 H 75-6L - Carbide Holder, L.H. 6” -
11 H 75-6R - Carbide Holder, R.H. 6” -
12 H 75-8L - Carbide Holder, L.H. 8” -
13 H 75-8R - Carbide Holder, R.H. 8” -
14 T 20034 - Terminator Tooth, 3⁄4" V-Carbide 0.8
15 T 20078 - Terminator Tooth, 7⁄8" V-Carbide 0.85
16 T 306706L - Terminator Adapter, L.H. 6” -
17 T 306706R - Terminator Adapter, R.H. 6” -
18 T 306708L - Terminator Adapter, L.H. 8” -
19 T 306708R - Terminator Adapter, R.H. 8” -
20 TP 17 - Heat Treated Tooth Pocket -
21 SP 1916 - 1 9⁄16" Alloy Tube Spacer -
22 SP 178 - 1 7⁄8" Alloy Tube Spacer -
23 SP 200 - 2”Alloy Tube Spacer -
24 SP 238 - 2 3⁄8" Alloy Tube Spacer -
25 SP 218 - 2 1⁄8" Alloy Tube Spacer -
26 34 FW - 3⁄4" Flat Washer -
27 34 LW - 3⁄4" Lock Washer -
28 34 LN - 3⁄4" Lock Nut -
29 34412-8 - 3⁄4" x 4 1⁄2" Gr. 8 Bolt -
30 34500-8 - 3⁄4" x 5” Gr. 8 Bolt -
31 34512-8   3⁄4" x 5 1⁄2" Gr. 8 Bolt  
32 34600-8 - 3⁄4" x 6” Gr. 8 Bolt -
33 PL 75-10 - 10” Carbide Expander -
34 PL 75-12 - 12” Carbide Expander -
35 PL 75-14 - 14” Carbide Expander -
36 PL 75-16 - 16” Carbide Expander -
37 BL 3110-10 - Block Spacer - Space for 2”Additional Cut -

Alligator and Bolt-on Rock & Frost Chain,Teeth & Adapters (41⁄2" Pitch 150,000# Test Chain) for DitchWitch® Models R100,AR12, R150

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A AL450008D24 Welded Alligator Chain, 8” Cut, 24 Stations -
2 B 135-812 B450000B24 18'0" Chain, Bare 360
3 B 105-372 - Locknut (3⁄4" N.C.) -
4 B 105-499 - Bolt (3⁄4" x 1 3⁄4") -
5 B 135-801 - Chain Pin -
6 B 135-802 - Key -
7 B 135-805 - Roller Link -
8 R 100CL - Conn. Link -
9 B 136-100 - Carbide Bit (Full Cap) (765 CB) -
10 B 136-101 - Carbide Bit (Half Cap) (765 MB) -
11 B 136-102 - Carbide Bit (Rock Buster) (765 HB) -
12 B 136-060 - Bit Adapter (Position 1) -
13 B 136-061 - Bit Adapter (Position 2) -
14 B 136-062 - Bit Adapter (Position 3) -
15 B 136-063 - Bit Adapter (Position 4) -
16 765 BLK - Tooth Holder 0.8
17 765 HDBLK - Heavy Duty Tooth Holder 1

Note: MTO adapters can be manufactured upon request.


H-Plate,Terminator® and Bolt-on Rock & Frost Chain,Teeth and Adapters for DitchWitch® Models R100, AR12, R150 using TA4086 Chain (225,000# Test) replaces 4.5" 150,000 Chains

Image of Numbered parts

Image of Numbered parts

Image of Numbered parts

Ref No. Part No. Smart Pt. No. Description Weight (lbs.)
1 N/A TA408608H26 4.086”P Welded H-Plate Chain, 8” Cut, 26 Stations -
2 N/A TA408600B26 4.086”P Chain, Bare, 26 Stations -
3 B 43 LH - Carbide Tooth with clip (735 MRW) -
4 B 43 LRB - Carbide Tooth with clip (735 HR) -
5 765 CRFN - Carbide Tooth with clip (Full Cap) -
6 B 43 LC - Lock Clip Only (K91) -
7 B 43 CW - Clip Wrench -
8 TP 17 - Heat Treated Tooth Pocket -
9 PL 75-12 - 12" Carbide Expander Plate -
10 PL 75-14 - 14" Carbide Expander Plate -
11 PL 75-16 - 16" Carbide Expander Plate -
N/S PL 75-18 - 18” Carbide Expander Plate -
N/S H 300-10L - Carbide Holder 10" Cut, L.H -
N/S H 300-10R - Carbide Holder 10" Cut, R.H. -
N/S H 300-12L - Carbide Holder 12" Cut, L.H. -
N/S H 300-12R - Carbide Holder 12" Cut, R.H. -
12 H 75-6L - Carbide Holder, L.H. 6” -
13 H 75-6R - Carbide Holder, R.H. 6” -
14 H 75-8L - Carbide Holder, L.H. 8” -
15 H 75-8R - Carbide Holder, R.H. 8” -
16 SP 2716 - 2 7⁄16”Alloy Tube Spacer -
17 SP 238 - 2 3⁄8”Alloy Tube Spacer -
18 SP 11516 - 1 15⁄16”Alloy Tube Spacer -
19 SP 2116 - 2 1⁄16”Alloy Tube Spacer -
20 BL 4086-10 - Block Spacer – Spacer for 2" Additional Cut -
21 T 306706L - Terminator Adapter, L.H. 6” -
22 T 306706R - Terminator Adapter, R.H. 6” -
23 T 306708L - Terminator Adapter, L.H. 8” -
24 T 306708R - Terminator Adapter, R.H. 8” -
25 T 20034 - Terminator Tooth, 3⁄4" V-Carbide 0.8
26 T 20078 - Terminator Tooth, 7⁄8" V-Carbide 0.85
27 B 83 LH - Carbide Tooth with clip -
28 B 83 LC - Lock Clip -
29 34 FW - 3⁄4” Flat Washer -
30 34 LW - 3⁄4” Lock Washer -
31 34 LN - 3⁄4” Lock Nut -
32 34412-8 - 3⁄4” x 41/2” Gr. 8 Bolt -
33 34500-8 - 3⁄4” x 5” Gr. 8 Bolt -
34 34512-8 - 3⁄4” x 51/2” Gr. 8 Bolt -
35 34600-8 - 3⁄4” x 6” Gr. 8 Bolt -
N/S 34 TABS - 3⁄4” Bolt Seat for TA300 Holder -
36 PL 300-16 - 16” Carbide Expander Plate -
37 PL 300-18 - 18” Carbide Expander Plate -
38 PL 300-20 - 20” Carbide Expander Plate -
N/S PL 300-22 - 22” Carbide Expander Plate -
N/S PL 300-24 - 24” Carbide Expander Plate -
© 2022 Maverick, Inc All rights reserved.